Description
Mean Well LRS-150-12 LED Power Supply – 12 V 150 W 12,5 A IP20
The 150 W metal LED power supply is designed for extensive lighting systems where the combined power consumption of several sections exceeds the capacity of smaller units. Its output voltage is 12 V DC, while the maximum current reaches 12,5 A.
This design includes a 115/230 V mains input range selector switch. Setting the switch correctly before starting the unit is essential for safety; connecting the power supply with an incorrect setting may damage the module.
The housing is made of perforated sheet metal, and the unit is 30 mm high. This version has a larger footprint than lower-power models, so sufficient space for wiring, installation and air circulation must be allowed when planning the enclosure.

12 V 150 W LED Power Supply for Larger Linear Lighting Installations
The 12,5 A output makes it easier to distribute power to several compatible loads, provided their combined consumption remains within the 150 W rating. Particularly with long cable runs, voltage drops and conductor sizes should be assessed to ensure that the different sections of the installation operate as intended.
Two AC voltage ranges are available on the input side: 85–132 V and 170–264 V. The model can also operate in 240–370 V DC installations, but the connection method must be matched to the unit’s specifications for each application.
Protection against overload, short circuits and excessive voltage is provided. Heat is dissipated through the metal housing by natural air circulation, so covering the perforations inside a confined enclosure may impair correct operation of the power supply.
The photograph shows the construction of the LRS series, while the exact dimensions of the 150 W version are listed below. The image shows an LRS series housing; the dimensions of this model are provided in the specifications. The product offered is the LRS-150-12 model with a 150 W output, not a lower-power supply.
Product Specifications
- Type: modular switching power supply
- Output voltage: 12 V DC
- Rated power: 150 W
- Output current: up to 12,5 A
- Mains input: 85–132 V AC or 170–264 V AC
- Input range selection: manual 115/230 V switch
- DC input: 240–370 V DC
- Housing ingress protection rating: IP20
- Housing material: metal
- Cooling: natural convection
- Protection: short circuit, overload, overvoltage
Product Dimensions
- Length: 15,9 cm
- Width: 9,7 cm
- Height: 3 cm
- Catalogue weight: 0,42 kg
- Installation: within an enclosure with adequate ventilation
Why Choose a 150 W Power Supply?
- Higher output capacity – a current of 12,5 A provides greater capacity for powering 12 V installations.
- Selectable input range – two AC input ranges selected using a 115/230 V switch.
- Low 30 mm profile – makes it easier to install the module in a prepared equipment cabinet.
- Metal housing – protects the internal components while providing ventilation openings.
- Electronic protection – helps protect the unit under fault conditions.
- Constant 12 V output – intended for devices with the same rated voltage.
Who Is This Product Suitable For?
This product may interest installers setting up display lighting, lighting systems with multiple sections and other 12 V systems with relatively high power requirements. It is suitable for projects requiring a single high-capacity module or extensive DC power distribution.
Installation in a dry, protected space is required, as the IP20 housing does not protect against water, and the terminal block remains accessible during servicing. Connection to the mains should be carried out by a qualified electrician, ensuring appropriate protection against contact with live parts and checking the voltage selector switch.
For an extensive installation, power cable routes, conductor sizes and connection point locations should be planned separately. Voltage drops may occur along longer cables, so spare power supply capacity alone does not replace proper electrical design. Appropriate load distribution and housing ventilation are essential during prolonged operation at high current draw.
Summary
The LRS-150-12 model delivers 150 W and a current of up to 12,5 A in a metal housing measuring 3 cm in height. It is suitable for properly designed 12 V LED systems and requires the input selector position and adequate ventilation to be checked before operation.









Reviews
There are no reviews yet.